The audio actually works, I went to settings and saw that there wasn’t any output. Everything ok, the game was perfect (60fps 100 speed) but no audio. Downloaded Dolphin 5.0 and installed it. I have a MacBook Pro mid 2012 Intel core i5 Intel HD Graphics 4000 4gb ram and installed Windows 7 Home Premium with bootcamp.
![]() □ “Sensor Bar” alternativesUnfortunately, by the time the controllers and game had arrived, the sensor bar that I'd ordered still hadn't! — However, infrared light is emitted elsewhere (such as from the candles I mentioned before □), so I temporarily just used a bright floor lamp to calibrate the Wiimote when first lauching the game. — It may even appear as being “connected” in your Mac's Bluetooth menu, as shown below: Screenshot of my Nintendo Wiimote connected via Bluetooth to my Mac.… Even if the controller is listed in your Mac's Bluetooth menu, though, you'll still need to repeat the steps above to reinitiate the connection whenever you reconnect it, as experienced at this time of writing. Then, immediately press the red “Sync” button on the back of the Wiimote!… If you're successful, the controller will stop flashing and you'll feel it vibrate briefly to indicate a successful pairing. Click the “ Refresh” button under the “Real Wiimotes” section. Choose “Real Wiimote” for Wiimote 1 controller (not “Emulated Wiimote”) — For more information on this, check out Dolphin's FAQs. □ Or, insert an actual Wii game disc into your computer's CD/DVD drive.Once the game is running, you should press “ Command (⌘) + 1” on your keyboard to enable the first controller, and then “ Command(⌘) + F” to make the game fullscreen.While Wii games are simple to launch, I imagine that there may be a different process for GameCube games given that its discs are physically much smaller than typical CDs/DVDs and therefore might not be safe to insert into your computer's CD drive, especially if it's slot-loading like the MacBook Pro's drives. □ Open “disk images” of any game discs that you've already created yourself. — UPDATE (7): I eventually just used a disposable lighter □ to emulate the sensor bar briefly when recalibating the Wiimote: Using a disposable lighter to calibrate a Wiimote without a sensor bar.Actually running games in the Dolphin Emulator is easy through options in the software's menus: I occasionally would need to reset it if it became off-target while playing, but I could do so in the “Pause” menu to not adversely affect gameplay. Dolphin Emulator Pro Portable Graphics ProcessorInstead, it was primarily the CPU that caused performance concerns during emulation! Recommended settingsI recommend changing the following settings from their defaults for “ The Legend of Zelda: Skyward Sword” to get decent playback results and less overall CPU usage on a 2013 15-inch MacBook Pro with discrete GPU.First, go to the “Settings” menu in Dolphin, and select the “ Graphics” option: (For this reason, I'm not sure if Dolphin will run well on the 13-inch MacBook Pro or other models with just the Intel GPU.)… Even with the game running at a super-high display resolution, I actually found that the graphics settings didn't bottleneck Dolphin's performance very much at all on this machine. The high-end 2013 15-inch MacBook Pro has a discrete GPU for high-performance rendering, alongside the basic Intel GPU that's more power-efficient and generally not used when doing anything intensive. Insane native display resolution for a portable graphics processor to handle (2880×1800) — For “ The Legend of Zelda: Skyward Sword”, I found that my frame-rate (before adjusting settings) was initially just 20 FPS! That is not playable or enjoyable, and I began to investigate options to improve the performance.Dolphin has their own performance guide, but for my particular computer, there were a few things in particular to take into account: In the “ Hacks” tab: (This is where things can get interesting…) (I did this for optimal visuals, and haven't notice a performance hit, but you could also try reducing this if you're running into issues.) “16x” for Anisotropic filtering. “None” for Anti-aliasing since you have a “HiDPI” Retina display. “Auto (Window Size)” for Internal resolution, or you may waste system resources doing artificial scaling… especially when switching to an external monitor or TV. Enable “ Hide Mouse Cursor” to prevent distraction. Where are dolphin emulator saves macDefinitely enable “ OpenMP Texture Decoder” on the newer MacBook Pro computers, as they have multiple CPU cores and this offers a huge performance boost. (I recommend enabling it unless it causes significant issues for you.)
0 Comments
Leave a Reply. |
AuthorCathy ArchivesCategories |